通風管道是可以保持室內空氣一直暢通，同時還可以降低有害氣體的一種市政基礎設施，它平時就安裝在離我們很近的地方，通風管道是空調系統的重要組成部分，通風管道是由風管加工設備制成的，但是在山東通風管道加工過程中會出現很多問題，比如以下問題。

The ventilation duct is a municipal infrastructure that can keep the indoor air unblocked and reduce harmful gases. It is usually installed close to us. The ventilation duct is an important part of the air conditioning system. The ventilation duct is made by the air duct processing equipment. However, there are many problems in the process of Shandong ventilation duct processing, such as the following problems.

1.嚴禁風管翹曲和彎頭

1. Warpage and elbow of air duct are strictly prohibited

(1)原因：板排列時，風管成對平行，相對的板長寬不相等。

(1) Cause: when the plates are arranged, the air ducts are parallel in pairs, and the length and width of the opposite plates are not equal.

(2)步驟：開啟下料時，板材的邊角應連接，并檢查每塊板材的長度、寬度和對角線，使誤差在允許范圍內;下料后，風管對面的兩塊板應重疊，以檢查尺寸精度。

(2) Step: when starting blanking, the edges and corners of plates shall be connected, and the length, width and diagonal of each plate shall be checked to make the error within the allowable range; After blanking, the two plates opposite the air duct shall be overlapped to check the dimensional accuracy.

(3)意味著兩對矩形風道是三維的，并且兩個端面不平行;折疊角度不直;對角線;的不平等咬得并不嚴格。

(3) It means that the two pairs of rectangular air ducts are three-dimensional and the two end faces are not parallel; The folding angle is not straight; Diagonal; The inequality of China is not strict.

(4)沖擊：會造成風管受力不均勻，安裝后風管不均勻，法蘭墊片松動，系統漏氣，造成空調負荷損失，延長使用壽命。

(4) Impact: it will cause uneven stress of air duct, uneven air duct after installation, loose flange gasket, air leakage of the system, loss of air conditioning load and extension of service life.

2.處理數據不符合標準

2. The processed data does not meet the standard

(1)原因：數據不合格，每一步制造風管的要求不嚴格。

(1) Cause: the data is unqualified and the requirements for each step of air duct manufacturing are not strict.

(2)步驟：在使用通風管道加工設備制造風管之前，需要對出廠合格證、數據質量確認、表面厚度等數據進行反思。確保數據可用性。

(2) Steps: before using the ventilation duct processing equipment to manufacture the air duct, it is necessary to reflect on the factory certificate, data quality confirmation, surface thickness and other data. Ensure data availability.

(3)板外不平整，厚度不均勻，有明顯的壓痕、裂紋、砂眼、疤痕、銹蝕等環境;風道在三維空間下沉，其前端向外突出并明顯變形。

(3) The outside of the plate is uneven, the thickness is uneven, and there are obvious indentation, crack, sand hole, scar, rust and other environments; The air duct sinks in three-dimensional space, and its front end protrudes outward and deforms obviously.

(4)影響：運行過程中風管泄漏，空調負荷增加，影響風的壽命和性能。

(4) Impact: during operation, the air duct leaks and the air conditioning load increases, affecting the service life and performance of the air.

通過以上文章，大家可以清楚的了解到通風管道加工時可能會遇見的問題，相信大家讀完這篇文章，可以對風管加工有一個更加深入的了解，后續大家想了解更多相關知識內容，可以持續關注我們的網站http://m.heblc.com，有什么需要大家隨時聯系我們。

Through the above articles, you can clearly understand the problems that may be encountered during the processing of ventilation ducts. I believe that after reading this article, you can have a deeper understanding of the processing of air ducts. In the future, if you want to know more about relevant knowledge, you can continue to pay attention to our website http://m.heblc.com Yes, please feel free to contact us if you need anything.